![]() So building a templated is key to sucess. Than you can save stuff and its saved in you project. ![]() You need to assign everything one time first. (the rotary controllers are working, I checked it out. I'm surprised I never stumbled on it! I'll dig into the 30 page, highly detailed pdf and assuming my brain doesn't explode, I'll see if I can get it to address those 8 rotary controllers. So maybe it's the right tool for you, too. Never the less it has a steep learning curve as well because it s a powerful tool, but there are good you tube documentation videos linked in the pdf manual. You are able to custimize you layout with different layers (so a layer for selected plugin (you can make a preset per specifit plugin), for tracks global etc.) I tryed it out a day ago with manjaro, and it made a good first impression. So where reaper is runnig sk2 shuold run, too. It's well documented (in my opignion) and its build with reaper scripts. What do you think about : Smart Knobs 2 (SK2) ? Can't really do any kind of mixing with it, but it does make transport control and macros accessible anywhere in the room. With the Flirc software, you you first setup what the computer will receive, like R for instance, then you press a key on whatever the IR device is you want to use, and it binds that action to the key. I use that to run REAPER from my drums which are across the room from the DAW machine. I bought a Flirc, which is an IR receiver that lets you use literally anything that transmits IR as a controller, and then turn the key presses into either normal keyboard keystrokes, multimedia commands, or other stuff like macro commands. One additional controller I use a lot for REAPER is the infrared remote that came with the HDTV I use as my DAW monitor. I setup the transport controls for REAPER on both, but so far haven't used the knobs or faders for anything in REAPER. That's a pretty cool setup! I have both an Akai MPD26 and M-Audio Oxygen Pro Mini that have faders, knobs, and transport controls. Post below if you have questions or suggestions on how to get more out of my X-Touch Compact. I hope this helps people in the future when thinking about adding a control surface to their setup. It's just like flying the Starship Enterprise. The monitor really makes up for no scribble-strip display.īelow is an image of my current setup with the X-Touch Compact and an Android pad loaded with my Web Browser Interface. Selecting a track on either the TCP or MCP banks the X-Touch and lights the Activation button. With the addition of the extra monitor, the control surface is much more useful. On the bottom right, Mackie assigned the Add Marker button. This has worked out very well, though I'm still bummed the rotary pots go to waste. What to do with 8 buttons on the controllers in the upper right? I set them to Automation modes: Read, Read/Trim, Latch, Write, etc. The box in the lower left is also handled by Mackie: Record The box in the upper left is provided by Mackie Control: Solo, Mute and Active track. ![]() I never got those to work under any software as pots, just as switches (pushing down on the rotary control activates a switch).Īny other unused buttons I was able to use by simply assigning them as shortcuts to Actions. Hit OK.Īt this point, everything works except the 8 rotary controls in the upper-right corner. Then select the MIDI ports to which the X-Touch Compact is connected. What finally worked best? The built-in Mackie Control in Reaper! To access it: I even did a fresh hard metal install to try it on a clean system, but no luck. Opening the config window to add hardware would lock up Reaper hard. That was annoying.ĭrivenByMoss - Linux support, but I could never get it to work. Worked OK on the Mackie Control setting, but the X-Touch wouldn't change banks to follow the selected mixer track. So I was using its Mackie Control setting instead. While it has settings for the X-Touch Compact, I could never get the specific config to load. It has some configs for specific hardware, and just about anything can be 'taught' to it, but the learning curve is like Mount Everest. ReaLearn - This is a great piece of software. This one hurt since this is the software featured in most of the YouTube videos. I really do appreciate all the hard work that developers put into creating their software, I just wish they spent a little more time in Linux.ĬSI - No Linux support. Here I'll run down the options available and what solution finally gave me the most control over the hardware. At this point, you'd think I'd be use to this Linux second class citizenship. I found out what that really means is: accessible if I'm running Mac or Windows. Before purchasing it, I watched LOTS of videos assuring me all the functions would be accessible. Several months ago, I dropped $225 to buy a Behringer X-Touch Compact off marketplace.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |